 |
Business | Industries | Finance | Tax |
| Index: > A B C D E F G H I J K L M N O P Q R S T U V W X Y Z |
|
|||||
| First Prev [ 1 2 3 4 ] Next Last |
A hard disk uses rigid rotating platters. It stores and retrieves digital data from a planar magnetic surface. Information is written to the disk by transmitting an electromagnetic flux through an antenna or write head that is very close to a magnetic material, which in turn changes its polarization due to the flux. The information can be read back in a reverse manner, as the magnetic fields cause electrical change in the coil or read head that passes over it.
A typical hard disk drive design consists of a central axis or spindle upon which the platters spin at a constant speed. Moving along and between the platters on a common armature are the read-write heads, with one head for each platter face. The armature moves the heads radially across the platters as they spin, allowing each head access to the entirety of the platter.
The associated electronics control the movement of the read-write armature and the rotation of the disk, and perform reads and writes on demand from the disk controller. Modern drive electronics are capable of scheduling reads and writes efficiently across the disk, and of remapping sectors of the disk which have failed.
Also, most major hard drive and motherboard vendors now support
S.M.A.R.T.technology, by which impending failures can often be predicted, allowing the user to be alerted in time to prevent data loss.
The (mostly) sealed enclosure protects the drive internals from dust, condensation, and other sources of contamination. The hard disk's read-write heads fly on an air bearing (a cushion of air) only nanometers above the disk surface. The disk surface and the drive's internal environment must therefore be kept immaculately clean, as fingerprints, hair, dust, and even smoke particles have mountain-sized dimensions when compared to the submicroscopic gap that the heads maintain.
Some people believe a disk drive contains a vacuum — this is incorrect, as the system relies on air pressure inside the drive to support the heads at their proper flying height while the disk is in motion. Another common misconception is that a hard drive is totally sealed. A hard disk drive requires a certain range of air pressures in order to operate properly. If the air pressure is too low, the air will not exert enough force on the flying head, the head will not be at the proper height, and there is a risk of head crashes and data loss. (Specially manufactured sealed and pressurized drives are needed for reliable high-altitude operation, above about 10,000 feet.) Some modern drives include flying height sensors to detect if the pressure is too low, and temperature sensors to alert the system to overheating problems.
Hard disk drives are not airtight. They have a permeable filter (a breather filter) between the top cover and inside of the drive, to allow the pressure inside and outside the drive to equalize while keeping out dust and dirt. The filter also allows moisture in the air to enter the drive. Very high humidity year-round will cause accelerated wear of the drive's heads (by increasing stiction, or the tendency for the heads to stick to the disk surface, which causes physical damage to the disk and spindle motor). You can see these breather holes on all drives -- they usually have a warning sticker next to them, informing the user not to cover the holes. The air inside the operating drive is constantly moving too, being swept in motion by friction with the spinning disk platters. This air passes through an internal filter to remove any leftover contaminants from manufacture, any particles that may have somehow entered the drive, and any particles generated by head crash.
Due to the extremely close spacing of the heads and disk surface, any contamination of the read-write heads or disk platters can lead to a head crash — a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film. For GMR heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) will still result in the head temporarily overheating, due to friction with the disk surface, and renders the disk unreadable until the head temperature stabilizes. Head crashes can be caused by electronic failure, a sudden power failure, physical shock, wear and tear, or poorly manufactured disks. Normally, when powering down, a hard disk moves its heads to a safe area of the disk, where no data is ever kept (the landing zone). However, especially in old models, sudden power interruptions or a power supply failure can result in the drive shutting down with the heads in the data zone, which increases the risk of data loss. Newer drives are designed such that the rotational inertia in the platters is used to safely park the heads in the case of unexpected power loss. In recent years, IBM pioneered drives with "head unloading" technology, where the heads are lifted off the platters onto "ramps" instead of having them rest on the platters. Other manufacturers have begun using this technology as well.
Spring tension from the head mounting constantly pushes the heads towards the disk. While the disk is spinning, the heads are supported by an air bearing, and experience no physical contact wear. The sliders (the part of the head that is closest to the disk and contains the pickup coil itself) are designed to reliably survive a number of landings and takeoffs from the disk surface, though wear and tear on these microscopic components eventually takes its toll. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear — when a drive is younger and has fewer start/stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage drive (literally, as the head drags along the drive surface until the air bearing is established). For the Maxtor DiamondMax series of drives, for instance, the drive typically has a 0.02% chance of failing after 4,500 cycles, a 0.05% chance after 7,500 cycles, with the chance of failure rising geometrically to 50% after 50,000 cycles, and increasing ever after.
Using rigid platters and sealing the unit allows much tighter tolerances than in a floppy disk. Consequently, hard disks can store much more data than floppy disk, and access and transmit it faster. In 2004, a typical workstation hard disk might store between 80 GB and 400 GB of data, rotate at 5400 to 10,000 rpm, and have an average transfer rate of over 30 MB/s. The fastest workstation hard drives spin at 15,000 rpm. Notebook hard drives, which are physically smaller than their desktop counterparts, tend to be slower and have less capacity. Most spin at only 4200 rpm or 5400 rpm, though the newest top models spin at 7200 rpm.
| Politics | Business | Finance |
 |
 |
 |
|